// SPDX-License-Identifier: (GPL-2.0+ OR BSD-2-Clause)
/*
 * Copyright (C) 2020 embedded brains GmbH.
 */

/dts-v1/;
#include "imx6ull.dtsi"
#include "imx6ull-phytec-phycore-som.dtsi"

/ {
	model = "GRiSP2";
	compatible = "embeddedbrains,grisp2", "phytec,imx6ull-pcl063-emmc", "fsl,imx6ull";

	gpio_leds_grisp2: leds {
		pinctrl-names = "default";
		pinctrl-0 = <&pinctrl_gpioleds_grisp2>;
		compatible = "gpio-leds";

		grisp-rgb1-red {
			gpios = <&gpio5 0 GPIO_ACTIVE_HIGH>;
		};
		grisp-rgb1-green {
			gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>;
		};
		grisp-rgb1-blue {
			gpios = <&gpio5 2 GPIO_ACTIVE_HIGH>;
		};
		grisp-rgb2-red {
			gpios = <&gpio5 3 GPIO_ACTIVE_HIGH>;
		};
		grisp-rgb2-green {
			gpios = <&gpio5 5 GPIO_ACTIVE_HIGH>;
		};
		grisp-rgb2-blue {
			gpios = <&gpio5 9 GPIO_ACTIVE_HIGH>;
		};
	};

	reg_usb1: regulator-usb1 {
		compatible = "regulator-fixed";
		pinctrl-names = "default";
		pinctrl-0 = <&pinctrl_usb1_en>;
		gpio = <&gpio2 8 GPIO_ACTIVE_HIGH>;

		regulator-name = "usb1";
		regulator-min-microvolt = <5000000>;
		regulator-max-microvolt = <5000000>;
		enable-active-high;

		status = "okay";
	};

	reg_usb2: regulator-usb2 {
		compatible = "regulator-fixed";
		pinctrl-names = "default";
		pinctrl-0 = <&pinctrl_usb2_en>;
		gpio = <&gpio3 16 GPIO_ACTIVE_HIGH>;

		regulator-name = "usb2";
		regulator-min-microvolt = <5000000>;
		regulator-max-microvolt = <5000000>;

		status = "okay";
	};

	pmod_i2c: pmod-i2c {
		pinctrl-names = "default", "gpio";
		pinctrl-0 = <&pinctrl_i2c2>;
		pinctrl-1 = <&pinctrl_i2c2_gpio>;
		status = "okay";

		/* I2C mode */
		grisp,i2c-alias = "i2c1"; /* use with i2c_bus_register_imx */
		grisp,int-gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
		grisp,reset-gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;

		/* GPIO mode */
		grisp,gpios =
			<&gpio1 8 GPIO_ACTIVE_HIGH>, /* X1403.1 */
			<&gpio1 9 GPIO_ACTIVE_HIGH>, /* X1403.2 */
			<&gpio1 30 GPIO_ACTIVE_HIGH>, /* X1403.3 */
			<&gpio1 31 GPIO_ACTIVE_HIGH>; /* X1403.4 */
	};

	pmod_spi: pmod-spi {
		pinctrl-names = "default", "gpio";
		pinctrl-0 = <&pinctrl_spi0>;
		pinctrl-1 = <&pinctrl_spi0_gpio>;
		status = "okay";

		/* SPI mode */
		grisp,spi-alias = "spi0"; /* use with spi_bus_register_imx */
		grisp,int-gpios = <&gpio4 19 GPIO_ACTIVE_HIGH>;

		/* GPIO mode */
		grisp,gpios =
			<&gpio3 10 GPIO_ACTIVE_HIGH>, /* X1402.1 */
			<&gpio4 27 GPIO_ACTIVE_HIGH>, /* X1402.2 */
			<&gpio4 28 GPIO_ACTIVE_HIGH>, /* X1402.3 */
			<&gpio4 25 GPIO_ACTIVE_HIGH>, /* X1402.4 */
			<&gpio4 19 GPIO_ACTIVE_HIGH>, /* X1402.7 */
			<&gpio4 24 GPIO_ACTIVE_HIGH>, /* X1402.8 */
			<&gpio3 11 GPIO_ACTIVE_HIGH>, /* X1402.9 */
			<&gpio3 12 GPIO_ACTIVE_HIGH>, /* X1402.10 */
			<&gpio4 26 GPIO_ACTIVE_HIGH>; /* X1401.1 */
	};

	pmod_gpio: pmod-gpio {
		pinctrl-names = "default";
		pinctrl-0 = <&pinctrl_gpio_pmod>;
		status = "okay";

		grisp,gpios =
			<&gpio1 1 GPIO_ACTIVE_HIGH>, /* X1404.1 */
			<&gpio1 5 GPIO_ACTIVE_HIGH>, /* X1404.2 */
			<&gpio1 3 GPIO_ACTIVE_HIGH>, /* X1404.3 */
			<&gpio1 4 GPIO_ACTIVE_HIGH>, /* X1404.4 */
			<&gpio1 20 GPIO_ACTIVE_HIGH>, /* X1404.7 */
			<&gpio3 7 GPIO_ACTIVE_HIGH>, /* X1404.8 */
			<&gpio1 22 GPIO_ACTIVE_HIGH>, /* X1404.9 */
			<&gpio1 23 GPIO_ACTIVE_HIGH>; /* X1404.10 */
	};

	pmod_uart: pmod-uart {
		pinctrl-names = "default", "gpio";
		pinctrl-0 = <&pinctrl_uart4>;
		pinctrl-1 = <&pinctrl_uart4_gpio>;
		status = "okay";

		/* UART mode */
		grisp,uartdev = "/dev/ttyS3";

		/* GPIO mode */
		grisp,gpios =
			<&gpio3 2 GPIO_ACTIVE_HIGH>, /* X1405.1 */
			<&gpio3 0 GPIO_ACTIVE_HIGH>, /* X1405.2 */
			<&gpio3 1 GPIO_ACTIVE_HIGH>, /* X1405.3 */
			<&gpio3 3 GPIO_ACTIVE_HIGH>, /* X1405.4 */
			<&gpio3 4 GPIO_ACTIVE_HIGH>, /* X1405.7 */
			<&gpio3 5 GPIO_ACTIVE_HIGH>, /* X1405.8 */
			<&gpio3 6 GPIO_ACTIVE_HIGH>, /* X1405.9 */
			<&gpio1 21 GPIO_ACTIVE_HIGH>; /* X1405.10 */
	};

	pin_gpio: pin-gpio {
		pinctrl-names = "default";
		pinctrl-0 = <&pinctrl_gpio_pins>;
		status = "okay";

		grisp,gpios =
			<&gpio1 24 GPIO_ACTIVE_HIGH>, /* X1300.3 */
			<&gpio1 25 GPIO_ACTIVE_HIGH>, /* X1300.4 */
			<&gpio1 26 GPIO_ACTIVE_HIGH>, /* X1300.5 */
			<&gpio1 27 GPIO_ACTIVE_HIGH>, /* X1300.6 */
			<&gpio4 16 GPIO_ACTIVE_HIGH>, /* X1301.3 */
			<&gpio4 17 GPIO_ACTIVE_HIGH>, /* X1301.4 */
			<&gpio4 18 GPIO_ACTIVE_HIGH>, /* X1301.5 */
			<&gpio4 20 GPIO_ACTIVE_HIGH>, /* X1301.6 */
			<&gpio4 21 GPIO_ACTIVE_HIGH>, /* X1301.7 */
			<&gpio4 22 GPIO_ACTIVE_HIGH>, /* X1301.8 */
			<&gpio4 23 GPIO_ACTIVE_HIGH>, /* X1301.9 */
			<&gpio2 10 GPIO_ACTIVE_HIGH>, /* X1301.10 */
			<&gpio2 11 GPIO_ACTIVE_HIGH>, /* X1301.11 */
			<&gpio2 12 GPIO_ACTIVE_HIGH>, /* X1301.12 */
			<&gpio2 13 GPIO_ACTIVE_HIGH>, /* X1301.13 */
			<&gpio2 14 GPIO_ACTIVE_HIGH>; /* X1301.14 */
	};

	jumper: jumper-keys {
		pinctrl-names = "default";
		pinctrl-0 = <&pinctrl_jumper>;
		status = "okay";

		grisp,gpios =
			<&gpio3 8 GPIO_ACTIVE_HIGH>, /* JUMPER1 */
			<&gpio3 9 GPIO_ACTIVE_HIGH>, /* JUMPER2 */
			<&gpio3 13 GPIO_ACTIVE_HIGH>, /* JUMPER3 */
			<&gpio3 14 GPIO_ACTIVE_HIGH>, /* JUMPER4 */
			<&gpio3 15 GPIO_ACTIVE_HIGH>; /* JUMPER5 */
	};
};

&fec1 {
	status = "okay";
};

&ethphy1 {
	status = "okay";
};

&i2c1 {
	status = "okay";

	ds2482s: onewire_master@18 {
		compatible = "maxim,ds2482s";
		reg = <0x18>;
		status = "okay";
	};
	at24mac402_eeprom: eeprom@57 {
		compatible = "atmel,24c02";
		reg = <0x57>;
		status = "okay";
	};
	at24mac402_eui: eeprom@5f {
		compatible = "atmel,at24mac402-eui";
		reg = <0x5f>;
		status = "okay";
	};
	atecc608: cryptoauth@36 {
		compatible = "microchip,atecc608", "atmel,at24c16";
		reg = <0x36>;
		status = "okay";
	};
};

&i2c2 {
	clock-frequency = <100000>;
	status = "okay";
};

&usbotg1 {
	pinctrl-names = "default";
	dr_mode = "host";
	vbus-supply = <&reg_usb1>;
	/* This removes the warning about not specifying anything for over-current handling */
	disable-over-current;
	status = "okay";
};

&usbotg2 {
	dr_mode = "host";
	vbus-supply = <&reg_usb2>;
	disable-over-current;
	status = "okay";
};

&usdhc1 {
	pinctrl-names = "default", "state_100mhz", "state_200mhz";
	pinctrl-0 = <&pinctrl_usdhc1>;
	pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
	pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
	cd-gpios = <&gpio1 19 GPIO_ACTIVE_HIGH>;
	no-1-8-v;
	keep-power-in-suspend;
	wakeup-source;
	status = "okay";
};

&usdhc2 {
	pinctrl-names = "default";
	non-removable;
	wakeup-source;
	status = "okay";
};

&uart4 {
	status = "okay";
};

&ecspi1 {
	status = "okay";

	cs-gpios = <&gpio4 26 GPIO_ACTIVE_HIGH>,
		   <&gpio3 10 GPIO_ACTIVE_HIGH>,
		   <&gpio3 11 GPIO_ACTIVE_HIGH>,
		   <&gpio3 12 GPIO_ACTIVE_HIGH>;
};

&iomuxc {
	pinctrl_i2c2: i2c2grp {
		fsl,pins = <
			MX6UL_PAD_UART5_TX_DATA__I2C2_SCL	0x4001b830	/* SCL_2; X1400.1; X1403.3 */
			MX6UL_PAD_UART5_RX_DATA__I2C2_SDA	0x4001b830	/* SDA_2; X1400.3; X1403.4 */
			MX6UL_PAD_GPIO1_IO08__GPIO1_IO08	0x3008		/* I2C_2_INT; X1403.1  */
			MX6UL_PAD_GPIO1_IO09__GPIO1_IO09	0x3008		/* I2C_2_RESET; X1403.2  */
		>;
	};

	pinctrl_i2c2_gpio: i2c2gpiogrp {
		fsl,pins = <
			MX6UL_PAD_UART5_TX_DATA__GPIO1_IO30	0x3008		/* SCL_2; X1400.1; X1403.3 */
			MX6UL_PAD_UART5_RX_DATA__GPIO1_IO31	0x3008		/* SDA_2; X1400.3; X1403.4 */
			MX6UL_PAD_GPIO1_IO08__GPIO1_IO08	0x3008		/* I2C_2_INT; X1403.1  */
			MX6UL_PAD_GPIO1_IO09__GPIO1_IO09	0x3008		/* I2C_2_RESET; X1403.2  */
		>;
	};

	pinctrl_usb1_en: usb1engrp {
		fsl,pins = <
			MX6UL_PAD_ENET2_RX_DATA0__GPIO2_IO08	0x08
		>;
	};

	pinctrl_usb2_en: usb2engrp {
		fsl,pins = <
			MX6UL_PAD_LCD_DATA11__GPIO3_IO16	0x08
		>;
	};

	pinctrl_usdhc1: usdhc1grp {
		fsl,pins = <
			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x17059
			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x10059
			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0	0x17059
			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1	0x17059
			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2	0x17059
			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3	0x17059
			MX6UL_PAD_UART1_RTS_B__GPIO1_IO19	0x17059
		>;
	};

	pinctrl_usdhc1_100mhz: usdhc1grp100mhz {
		fsl,pins = <
			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x170b9
			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x100b9
			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0	0x170b9
			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1	0x170b9
			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2	0x170b9
			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3	0x170b9
			MX6UL_PAD_UART1_RTS_B__GPIO1_IO19	0x17059
		>;
	};

	pinctrl_usdhc1_200mhz: usdhc1grp200mhz {
		fsl,pins = <
			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x170f9
			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x100f9
			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0	0x170f9
			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1	0x170f9
			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2	0x170f9
			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3	0x170f9
			MX6UL_PAD_UART1_RTS_B__GPIO1_IO19	0x17059
		>;
	};

	pinctrl_spi0: spi0grp {
		fsl,pins = <
			MX6UL_PAD_CSI_DATA04__ECSPI1_SCLK	0x8	/* SPI_SCK; X1401.4; X1402.4 */
			MX6UL_PAD_CSI_DATA06__ECSPI1_MOSI	0x8	/* SPI_MOSI; X1401.2; X1402.2 */
			MX6UL_PAD_CSI_DATA07__ECSPI1_MISO	0x2000	/* SPI_MISO; X1401.3; X1402.3 */
			MX6UL_PAD_CSI_DATA05__GPIO4_IO26	0x8	/* SPI_SS0 ; X1401.1 */
			MX6UL_PAD_LCD_DATA05__GPIO3_IO10	0x8	/* SPI_SS1 ; X1402.1 */
			MX6UL_PAD_LCD_DATA06__GPIO3_IO11	0x8	/* SPI_SS2 ; X1402.9 */
			MX6UL_PAD_LCD_DATA07__GPIO3_IO12	0x8	/* SPI_SS3 ; X1402.10 */
			MX6UL_PAD_CSI_DATA03__GPIO4_IO24	0x8	/* SPI_RESET ; X1402.8 */
			MX6UL_PAD_CSI_VSYNC__GPIO4_IO19		0x8	/* SPI_INT ; X1402.7 */
		>;
	};

	pinctrl_spi0_gpio: spi0gpiogrp {
		fsl,pins = <
			MX6UL_PAD_CSI_DATA04__GPIO4_IO25	0x3008	/* SPI_SCK; X1401.4; X1402.4 */
			MX6UL_PAD_CSI_DATA06__GPIO4_IO27	0x3008	/* SPI_MOSI; X1401.2; X1402.2 */
			MX6UL_PAD_CSI_DATA07__GPIO4_IO28	0x3008	/* SPI_MISO; X1401.3; X1402.3 */
			MX6UL_PAD_CSI_DATA05__GPIO4_IO26	0x3008	/* SPI_SS0 ; X1401.1 */
			MX6UL_PAD_LCD_DATA05__GPIO3_IO10	0x3008	/* SPI_SS1 ; X1402.1 */
			MX6UL_PAD_LCD_DATA06__GPIO3_IO11	0x3008	/* SPI_SS2 ; X1402.9 */
			MX6UL_PAD_LCD_DATA07__GPIO3_IO12	0x3008	/* SPI_SS3 ; X1402.10 */
			MX6UL_PAD_CSI_DATA03__GPIO4_IO24	0x3008	/* SPI_RESET ; X1402.8 */
			MX6UL_PAD_CSI_VSYNC__GPIO4_IO19		0x3008	/* SPI_INT ; X1402.7 */
		>;
	};

	pinctrl_uart4: uart4grp {
		fsl,pins = <
			MX6UL_PAD_LCD_HSYNC__UART4_DCE_CTS	0x1b008	/* CTS_4; X1405.1  */
			MX6UL_PAD_LCD_CLK__UART4_DCE_TX		0x1b008	/* TXD_4; X1405.2  */
			MX6UL_PAD_LCD_ENABLE__UART4_DCE_RX	0x1b008	/* RXD_4; X1405.3  */
			MX6UL_PAD_LCD_VSYNC__UART4_DCE_RTS	0x1b008	/* RTS_4; X1405.4  */
			MX6UL_PAD_LCD_RESET__GPIO3_IO04		0x3008	/* GPIO3_04; X1405.7  */
			MX6UL_PAD_LCD_DATA00__GPIO3_IO05	0x3008	/* GPIO3_05; X1405.8  */
			MX6UL_PAD_LCD_DATA01__GPIO3_IO06	0x3008	/* GPIO3_06; X1405.9  */
			MX6UL_PAD_UART2_RX_DATA__GPIO1_IO21	0x3008	/* GPIO1_21; X1405.10 */
		>;
	};

	pinctrl_uart4_gpio: uart4gpiogrp {
		fsl,pins = <
			MX6UL_PAD_LCD_HSYNC__GPIO3_IO02		0x3008	/* CTS_4; X1405.1  */
			MX6UL_PAD_LCD_CLK__GPIO3_IO00		0x3008	/* TXD_4; X1405.2  */
			MX6UL_PAD_LCD_ENABLE__GPIO3_IO01	0x3008	/* RXD_4; X1405.3  */
			MX6UL_PAD_LCD_VSYNC__GPIO3_IO03		0x3008	/* RTS_4; X1405.4  */
			MX6UL_PAD_LCD_RESET__GPIO3_IO04		0x3008	/* GPIO3_04; X1405.7  */
			MX6UL_PAD_LCD_DATA00__GPIO3_IO05	0x3008	/* GPIO3_05; X1405.8  */
			MX6UL_PAD_LCD_DATA01__GPIO3_IO06	0x3008	/* GPIO3_06; X1405.9  */
			MX6UL_PAD_UART2_RX_DATA__GPIO1_IO21	0x3008	/* GPIO1_21; X1405.10 */
		>;
	};

	pinctrl_gpioleds_grisp2: gpioledsgrisp2grp {
		fsl,pins = <
			MX6UL_PAD_SNVS_TAMPER0__GPIO5_IO00	0x00088
			MX6UL_PAD_SNVS_TAMPER1__GPIO5_IO01	0x00088
			MX6UL_PAD_SNVS_TAMPER2__GPIO5_IO02	0x00088
			MX6UL_PAD_SNVS_TAMPER3__GPIO5_IO03	0x00088
			MX6UL_PAD_SNVS_TAMPER5__GPIO5_IO05	0x00088
			MX6UL_PAD_SNVS_TAMPER9__GPIO5_IO09	0x00088
		>;
	};

	pinctrl_gpio_pmod: gpiopmodgrp {
		fsl,pins = <
			MX6UL_PAD_GPIO1_IO01__GPIO1_IO01	0x3008 /* DIO1/AN1; X1404.1  */
			MX6UL_PAD_GPIO1_IO05__GPIO1_IO05	0x3008 /* DIO2/AN2; X1404.2  */
			MX6UL_PAD_GPIO1_IO03__GPIO1_IO03	0x3008 /* DIO3/AN3; X1404.3  */
			MX6UL_PAD_GPIO1_IO04__GPIO1_IO04	0x3008 /* DIO4/AN4; X1404.4  */
			MX6UL_PAD_UART2_TX_DATA__GPIO1_IO20	0x3008 /* DIO5; X1404.7  */
			MX6UL_PAD_LCD_DATA02__GPIO3_IO07	0x3008 /* DIO6; X1404.8  */
			MX6UL_PAD_UART2_CTS_B__GPIO1_IO22	0x3008 /* DIO7; X1404.9  */
			MX6UL_PAD_UART2_RTS_B__GPIO1_IO23	0x3008 /* DIO8; X1404.10 */
		>;
	};

	pinctrl_jumper: jumpergrp {
		fsl,pins = <
			MX6UL_PAD_LCD_DATA03__GPIO3_IO08	0x7000 /* JUMPER1 */
			MX6UL_PAD_LCD_DATA04__GPIO3_IO09	0x7000 /* JUMPER2 */
			MX6UL_PAD_LCD_DATA08__GPIO3_IO13	0x7000 /* JUMPER3 */
			MX6UL_PAD_LCD_DATA09__GPIO3_IO14	0x7000 /* JUMPER4 */
			MX6UL_PAD_LCD_DATA10__GPIO3_IO15	0x7000 /* JUMPER5 */
		>;
	};

	pinctrl_gpio_pins: gpiopinsgrp {
		fsl,pins = <
			MX6UL_PAD_UART3_TX_DATA__GPIO1_IO24	0x3008 /* GPIO1_IO24; X1300.3 */
			MX6UL_PAD_UART3_RX_DATA__GPIO1_IO25	0x3008 /* GPIO1_IO25; X1300.4 */
			MX6UL_PAD_UART3_CTS_B__GPIO1_IO26	0x3008 /* GPIO1_IO26; X1300.5 */
			MX6UL_PAD_UART3_RTS_B__GPIO1_IO27	0x3008 /* GPIO1_IO27; X1300.6 */

			MX6UL_PAD_NAND_DQS__GPIO4_IO16		0x3008 /* GPIO4_IO16; X1301.3 */
			MX6UL_PAD_CSI_MCLK__GPIO4_IO17		0x3008 /* GPIO4_IO17; X1301.4 */
			MX6UL_PAD_CSI_PIXCLK__GPIO4_IO18	0x3008 /* GPIO4_IO18; X1301.5 */
			MX6UL_PAD_CSI_HSYNC__GPIO4_IO20		0x3008 /* GPIO4_IO20; X1301.6 */
			MX6UL_PAD_CSI_DATA00__GPIO4_IO21	0x3008 /* GPIO4_IO21; X1301.7 */
			MX6UL_PAD_CSI_DATA01__GPIO4_IO22	0x3008 /* GPIO4_IO22; X1301.8 */
			MX6UL_PAD_CSI_DATA02__GPIO4_IO23	0x3008 /* GPIO4_IO23; X1301.9 */
			MX6UL_PAD_ENET2_RX_EN__GPIO2_IO10	0x3008 /* GPIO2_IO10; X1301.10 */
			MX6UL_PAD_ENET2_TX_DATA0__GPIO2_IO11	0x3008 /* GPIO2_IO11; X1301.11 */
			MX6UL_PAD_ENET2_TX_DATA1__GPIO2_IO12	0x3008 /* GPIO2_IO12; X1301.12 */
			MX6UL_PAD_ENET2_TX_EN__GPIO2_IO13	0x3008 /* GPIO2_IO13; X1301.13 */
			MX6UL_PAD_ENET2_TX_CLK__GPIO2_IO14	0x3008 /* GPIO2_IO14; X1301.14 */
		>;
	};
};

/*
 * Nerves additions
 */
#include <dt-bindings/leds/common.h>

&gpio_leds_grisp2 {
        /* Provide LEDs with colors and functions to be consistent with Linux conventions */
	grisp-rgb1-red {
		function = LED_FUNCTION_INDICATOR;
		function-enumerator = <1>;
		color = <LED_COLOR_ID_RED>;
	};
	grisp-rgb1-green {
		function = LED_FUNCTION_INDICATOR;
		function-enumerator = <1>;
		color = <LED_COLOR_ID_GREEN>;
	};
	grisp-rgb1-blue {
		function = LED_FUNCTION_INDICATOR;
		function-enumerator = <1>;
		color = <LED_COLOR_ID_BLUE>;
	};
	grisp-rgb2-red {
		function = LED_FUNCTION_INDICATOR;
		function-enumerator = <2>;
		color = <LED_COLOR_ID_RED>;
	};
	grisp-rgb2-green {
		function = LED_FUNCTION_INDICATOR;
		function-enumerator = <2>;
		color = <LED_COLOR_ID_GREEN>;
	};
	grisp-rgb2-blue {
		function = LED_FUNCTION_INDICATOR;
		function-enumerator = <2>;
		color = <LED_COLOR_ID_BLUE>;
	};
};

/* Allow GPIOs to be accessible to userland */
&jumper {
        /delete-property/ grisp,gpios;
};
&pmod_gpio {
        /delete-property/ grisp,gpios;
};
&pin_gpio {
        /delete-property/ grisp,gpios;
};